Arctic Cat Sno Pro 120 2011 страница 129 Скачать руководство пользователя

Страница: 129 / 535

2-91

FC044

2. The trueness (out-of-roundness) is the difference

between the highest and lowest reading. Maximum

trueness (out-of-roundness) must not exceed 0.004

in.

0725-586

PISTON SKIRT/CYLINDER
CLEARANCE

1. Measure each cylinder front to back about 1 in. from

the bottom of each cylinder.

2. Measure the corresponding piston skirt diameter at a

point 1 cm above the piston skirt at a right angle to

the piston-pin bore. Subtract this measurement from

the measurement in step 1. The difference (clear-

ance) must be within 0.0030-0.0041 in.

AC091

PISTON-RING END GAP

1. Place each piston ring in the wear portion above the

exhaust port of its respective cylinder. Use the piston

to position each ring squarely in each cylinder.

2. Using a feeler gauge, measure each piston-ring end

gap. Acceptable ring end gap must be within 0.0120-

0.0196 in.

FC045

PISTON PIN AND PISTON-PIN
BORE

1. Measure the piston pin diameter at each end and in

the center. Acceptable piston pin measurement must

be within 0.8659-0.8661 in. for the 800 cc or 0.9447-

0.9449 in. for the 1000 cc. If any measurement varies

by more than 0.001 in., the piston pin and bearing

must be replaced as a set.

IO012

2. Insert a snap gauge into each piston-pin bore; then

remove the gauge and measure it with a micrometer.

The diameter measurement must be within 0.8661-

0.8665 in. for the 800 cc or 0.9450-0.9453 in. for the

1000 cc. Take two measurements to ensure accuracy.

AC092

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды