Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 257 / 535

background image

4

4-31

10. Install the carburetors/throttle bodies.

Synchronizing Oil-

Injection Pump



NOTE: On certain models, the oil pump cable

adjuster is located at the juncture of the throttle
cable.

0744-532

742-331B

738-338D

0744-528

INSPECTING/ADJUSTING/
SYNCHRONIZING

1. With the engine off on models with a cable operated

oil pump, disconnect the throttle cable from the

throttle lever.

2. Pull the throttle cable to the FULL-OPEN position;

then using a suitable clamping device, secure the

cable in this position.



NOTE: On models with a control rod operated oil

pump, rotate the control arm until it contacts the stop
screw.

3. Check to be sure the mark on the control arm is

aligned with alignment mark on the oil pump boss.

4. If the marks are not aligned, adjust synchronization

by loosening the jam nut(s) on the adjuster. Rotate

the jam nuts/adjuster nut until proper alignment is

attained. Tighten jam nut(s).

5. Return the control arm/throttle cable to the CLOSED

position.



NOTE: On models with a cable operated oil pump,

connect the throttle cable to the throttle lever; then
adjust the cable/linkage adjusting nut so the throttle
lever moves approximately 1/8 in. before the oil-injec-
tion pump control arm begins to move. This ensures
the throttle/ignition monitor switch will function prop-
erly and will prevent ignition “cut-out” and spark plug
fouling at low RPM operation.

CAUTION

Use a 100:1 fuel mixture for the following procedure.

570 cc

500 cc

600 cc

CAUTION

Care must be taken when securing the cable not to
kink or damage the cable.

CAUTION

Whenever servicing the oil-injection system, use a
100:1 gas/oil mixture in the gas tank to ensure ade-
quate engine lubrication. Failure to use the 100:1 mix-
ture to the oil-injection system will result in severe
engine damage.

CAUTION

Assure that the throttle cable/linkage has returned to
the fully closed (idle) position and has not remained in
a partial open position and moves freely from the open
position to the closed position.

800/1000 cc

Manual

Table of Contents

«
...
255
256
257
258
259
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Ski-Doo Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды