Arctic Cat Sno Pro 120 2011 страница 68 Скачать руководство пользователя

Страница: 68 / 535

2-30

FS177A

5. On the 500/600 cc, position the engine to the chassis

mounts; then in order, install cap screws (D) securing

the engine plate to the front chassis mounts; then

install cap screw (E) securing the MAG-side mount-

ing bracket to the chassis, and cap screw (D) to the

PTO-side mount. Tighten the cap screws to 50 ft-lb.

6. On the 800 cc, position the engine to the chassis

mounts; then install cap screw (E) securing the

MAG-side mounting bracket to the chassis. Tighten

cap screw to 50 ft-lb.

7. On the 800 cc, release the tie-down securing the

engine/pinion bracket in the forward position; then

position the engine to the bracket and secure with

four cap screws (D) (coated with blue Loctite #243).

Tighten to 50 ft-lb.

8. Position the torque bumper against the gear case;

then install the PTO-side engine mounting bracket.



NOTE: Prior to installing the bracket, assure the U-

nut clip is centered in position.

FS195A

9. Using the illustration following step 2, install the cap

screw and lock nut (A) and the lower cap screw (B)

securing the PTO-side bracket to the chassis; then

install the four cap screws (C) (coated with blue Loc-

tite #243) securing the bracket to the engine. Tighten

all mounting hardware to 23 ft-lb.

10. Connect the coolant hose to the outlet of the front

heat exchanger and secure with the hose clamp.

FS196A

11. Route the ignition harness and the coolant tempera-

ture sensor two-wire connector between the coolant

tank and the chassis; then connect all ignition/main

harness plug-ins and the two-wire connector.

FS197



NOTE: Prior to connecting the harness, clean all

plug-ins with contact cleaner and compressed air.

12. Secure the ignition harness to the coolant hose with a

cable tie in the position as noted in removing; then

install the harness wrap.

FS181

13. On the 800 cc LXR, install the starter motor using

the following sequence:

! WARNING

Always wear safety glasses when drying components
with compressed air.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды