Arctic Cat Sno Pro 120 2011 страница 407 Скачать руководство пользователя

Страница: 407 / 535

7-39

3. Inspect the outer rubber portion of the idler wheels

for cracks and poor bonding.

4. Inspect the plastic insert of each idler wheel for

cracks.

5. Inspect the shaft for wear and damaged threads.

6. Inspect all idler wheel bearings. Turn each bearing

(by hand) and if any roughness or binding is noted,

replace the bearing.

7. If a bearing must be replaced, see Idler Wheels/

Mounting Blocks - Cleaning and Inspecting in this

sub-section.

ASSEMBLING

742-873A

1. In order from the right-hand side, slide the axle

through the slide rail axle slot; then place a bushing

(E), inner idler wheel (D), rear idler wheel spacer

(C), inner idler wheel (D), and bushing (E) on the

axle. Slide the axle through the opposite slide rail

axle slot.

2. Place the adjuster bushings (A) on the axle (on the

outside of each axle slot); then install the outer idler

wheels on the axle and secure with two cap screws

(coated with blue Loctite #243) and large flat wash-

ers. Tighten cap screws only until snug.

ZJ266

FC194



NOTE: Tighten the rear idler wheel axle only until

snug until the skid frame has been installed and track
tension has been adjusted; then the axle assembly
must be tightened to 40 ft-lb.

3. Install the skid frame (see Installing Skid Frame in

this sub-section).

Rear Arm/Idler Arm



NOTE: The skid frame must be removed for this pro-

cedure (see Removing Skid Frame in this sub-sec-
tion).

DISASSEMBLING

1. Remove the rear upper idler wheels and springs (see

Rear Upper Idler Wheels/Rear Springs in this sub-

section).

MS153

2. Remove the cap screw and lock nut securing the

upper shock eyelet to the idler arm. Account for a

spacer, cap screw, and lock nut.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды