manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 355 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 355

6-32

ADJUSTING DEFLECTION

1. Place the snowmobile up on a shielded safety stand.

Check to make sure the track is 2-3 in. off the floor.

2. If the measurement is not as specified, loosen the

jam nuts of the adjusting bolts.

0742-921

3. If the measurement obtained in step 2 is more than

specified, tighten the adjusting bolts. If the measure-

ment obtained is less than specified, loosen the

adjusting bolts. When the measurement is within

specification range, lock the adjustment by bottom-

ing the jam nuts against the axle housings.

NOTE: If the track tension must be loosened, it may

be necessary to loosen the rear axle assembly
slightly.

NOTE: Vigorously push the underside of the track

up and down. Track must not hit the top of the tunnel
or slap the skid frame.

4. After correct track tension is obtained, check track

alignment (see Track Alignment in this section).

NOTE: Track tension and track alignment are interre-

lated; always check both even if only one adjustment
seems necessary. Always establish correct track ten-
sion before checking and/or adjusting alignment.

Track Alignment

NOTE: Proper track alignment is when the rear idler

wheels are equidistant from the inner drive lugs on
the inside surface of the track.

CHECKING

1. Using a shielded safety stand, raise the rear of the

snowmobile off the floor making sure the track is

free to rotate.

2. Start the engine and accelerate slightly. Use only

enough throttle to rotate the track several revolu-

tions. SHUT THE ENGINE OFF.

NOTE: Allow the track to coast to a stop. Do not

apply the brake because it could produce inaccurate
alignment conditions.

3. When the track stops rotating, check the relationship

of the rear idler wheels and the inner track drive lugs.

If the distance from the idler wheels to the inner

drive lugs is the same on both sides, no adjustment is

necessary.

725-070A

4. On the side of the track, which has the inner drive

lugs closer to the rear idler wheel, loosen the adjust-

ing bolt jam nut; then rotate the adjusting bolt clock-

wise 1-1 1/2 turns.

5. Continue to check the track alignment and make the

necessary adjustments until proper alignment is

obtained.

6. After proper track alignment is obtained, lock the

jam nut against the axle housing.

NOTE: Make sure correct track tension is main-

tained after adjusting track alignment.

NOTE: Field test the track under actual conditions

and after the field test, check track alignment and
track tension; adjust as necessary.

Brake System (Hydraulic)

CHECKING BRAKE LEVER TRAVEL

1. Compress the brake lever fully.

CAUTION

After proper track tension and alignment have been
attained, make certain that the rear axle assembly is
tightened to specifications or component damage will
occur.

! WARNING

The tips of the skis must be positioned against a wall
or similar object for safety. Keep hands, feet, and
clothing away from moving components.

CAUTION

After proper track tension and alignment have been
attained, make certain that the rear axle assembly is
tightened to 40 ft-lb or component damage will occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов