Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 343

Страница: 343 / 535

6-20

1. Wash the gear case halves and unsealed bearing in

parts-cleaning solvent.

2. Inspect the gear case halves for trueness, scoring, pit-

ting, scuffing, or any imperfections in the casting.

3. Inspect all threaded areas for damaged or stripped

threads.

4. Inspect the bearing areas for cracks or excessive

bearing movement. If evidence of excessive bearing

movement is noted, replace the component.

5. Inspect the gears for wear, cracks, or chipped teeth.

6. Inspect the input shaft/transfer gear bearings for

wear, scoring, scuffing, damage, or discoloration.

Rotate the bearings. Bearings must rotate freely and

must not bind or feel rough. If any abnormal condi-

tion is noted, replace the bearing.



NOTE: The output shaft bearing is a non-service-

able component. If any damage or binding is noted,
the output shaft assembly must be replaced.

7. Apply a light film of Arctic Cat Synthetic ACT

Drive Fluid to the unsealed bearings prior to assem-

bling.

ASSEMBLING GEAR CASE
(w/Reverse)

1. With the narrow, raised edges of the seal (A) facing

outward and using an appropriate seal installation

tool, install the oil seal into the output shaft opening

of the gear case.



NOTE: Grease must be applied to the seal prior to

installing.

ZJ303A

ZJ304



NOTE: Always install the seal with the wide, raised

edge of the seal facing against the seal surface of the
gear case.

ZJ305A

2. Place the output shaft assembly into position in the

slider housing; then secure the assembly to the hous-

ing with the thrust washer and retaining ring.

ZJ200

3. Using a suitable bearing press, install the bearing

onto the ring gear.

ZJ199

4. In order, install the thrust washer and then the thrust

bearing onto the transfer gear shaft.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 343 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: