manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 291 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 291

5-30

NOTE: If this resistance test does not read within

specification, troubleshoot the switch connector
located below the steering support. If the switch con-
nector tests good, replace the switch.

PASSENGER HEATER SWITCH - 
Resistance

1. Disconnect the main harness/element connector.

2. Connect one ohmmeter lead to the red/blue main har-

ness connector; then connect the other ohmmeter

lead to the green/red main harness connector. The

meter must read the following ± 5%:

NOTE: If this resistance test does not read within

specification, troubleshoot the switch connector
located beneath the seat. If the switch connector test
good, replace the switch.

OPERATOR/PASSENGER SWITCH - 
Voltage

1. Disconnect the main harness/element connector.

NOTE: For this procedure, test the main harness

side of the connector, not the element side of the
connector.

2. Connect one meter lead to the red/blue main harness

connector; then connect the other meter lead to the

black main harness connector.

3. Start the engine. The meter must read 12-15 volts.

NOTE: If this voltage test does not read within spec-

ification, troubleshoot the main harness, F-2 fuse, K-
2 relay, or the F-7 main fuse.

Testing Speedometer 

Sensor

NOTE: The following test should be made using

MaxiClips and the Fluke Model 77 Multimeter set to
the DC Volt scale.

NOTE: Prior to testing the sensor, inspect the three-

wire connector on the sensor harness for contamina-
tion, broken pins, and/or corrosion. With the engine
running, note that a power supply of 10.8-13.2 DC
volts exists at the main harness/speedometer con-
nector.

ZJ210B

1. Elevate the rear of the snowmobile onto a suitable

safety stand.

2. Set the meter selector to the DC Voltage position.

3. At the sensor side of the plug-in, connect the red

maxiclip and meter lead to the white (center) lead;

then connect the black maxiclip and meter lead to the

black lead.

4. Connect a positive 12-volt DC power supply to the

red/blue wire; then connect a negative cable to the

black wire from the main harness side of the plug-in.

5. Rotate the driven pulley. The meter must read 0 volts

and 12 volts alternately.

NOTE: No voltage should appear when the tab (A) of

the brake disc jam nut is aligned with the sensor (B).

ZJ210C

Testing Reverse Alarm 

Switch

NOTE: The switch is located on the gear case above

the left-side footrest.

1. Disconnect the alarm switch two-wire connector.

2. Remove the six torx-head cap screws securing the left-

side footrest to the chassis and remove the footrest;

then un-thread the alarm switch from the gear case.

3. Connect one ohmmeter lead to the red/blue (570/800

cc), red/green (1100 cc), or red/black (500/600 cc)

wire; then connect the other ohmmeter lead to the

violet/black wire.

LO

4.32K ohms

MED

3.92K ohms

HI

3.57K ohms

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов