manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 145 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 145

2-107

2

TZ085A

26. Remove the two cap screws securing the intake pipe

to the cylinder head cover; then remove the remain-

ing cap screw securing the pipe to the left side of the

cylinder head.

TZ085B

TZ099A

27. Disconnect the throttle position sensor, air tempera-

ture sensor, boost sensor, and cam position sensor.

743-999A

28. From the opposite side of the throttle body, discon-

nect the idle speed control and the throttle cable.

0743-992

29. Remove the spark plug wires from the spark plugs.

30. Loosen the flange clamps securing the intake mani-

fold to the cylinder head; then remove the manifold

and throttle body assembly along with the two

flanges.

TZ090A

31. Remove the positive cable from the starter motor.

32. On the non-turbo models, disconnect the harness

plug-ins from the ignition coils (A) and camshaft

timing sensor (B).

ZJ094A

NOTE: With the main harness plug-ins discon-

nected, secure the harness up and out of the way
from the engine. 

33. On the non-turbo models, loosen the clamps securing

the throttle body assembly to the intake flanges; then

remove the assembly and allow it to lie on the tunnel. 

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов