Arctic Cat Sno Pro 120 2011 страница 455 Скачать руководство пользователя

Страница: 455 / 535

7-87

FZ077

12. With the spacer on the front rail support centered

between the limiter straps, secure the straps to the

rail support with the cap screw, washers, and lock

nut. Tighten to 120 in.-lb.

FZ078A

13. Secure the end cap onto the slide rail using a cap

screw, flat washers, and a lock nut. Tighten to 80 in.-

lb.

FZ079A



NOTE: Apply a light coat of grease to the slide rail

surface to aid in installing a new wear strip. Use a file
to remove any sharp edges on the lower portion of
the rail.

MS288

14. From the back, start the wear strip onto the rail; then

using a soft hammer, drive the wear strip forward

into position. Secure with a torx-head screw and lock

nut. Tighten to 50 in.-lb.

MS207

MS016B

15. Install the skid frame (see Installing Skid Frame in

this sub-section).



NOTE: Install the rear arm springs onto the adjuster

blocks after the skid frame has been installed.

Installing Skid Frame

1. Using a piece of cardboard on the floor to protect

against scratching, tip the snowmobile onto one side.

2. Pull the track away from the tunnel and spread open;

then place the skid frame into the track.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды