Arctic Cat Sno Pro 120 2011 страница 490 Скачать руководство пользователя | Manualshive

Страница: 490 / 535

background image

7-122

AG261



NOTE: With the eyelet removed, inspect the bottom-

out bumper for cracks or wear.

INSTALLING

1. Clean shaft threads and eyelet threads.

2. Apply red Loctite #271 to both threads, install the

eyelet, and tighten securely.

Pressurizing Rebuildable

Shocks

To pressurize the gas shock absorber, a regulator system

and a nitrogen tank will be needed.

AG271



NOTE: Before inserting the needle into the bladder,

lubricate the needle with light oil to make installation
easier.

1. Insert the Inflation Needle into the shock bladder;

then open the valve on the filler handle.

FS079

2. Turn the nitrogen tank valve open and slowly rotate

the regulator T-handle inward until the gauge reads

200 lb of pressure; then close filler valve and remove

inflation needle.

3. Install the screw or the air valve ball (Fox Float

Shock) into the bladder housing and tighten securely.

4. With the reservoir pressurized, push down on the

shock shaft until it nearly bottoms and release it. The

shaft should return to its extended position smoothly.



NOTE: If a soft spot or a mushy area is felt as the

shaft is pushed down, this would indicate air in the
shock body. If there is air in the shock body, dis-
charge the reservoir gas pressure. Disassemble the
shock to the point that the “filling with oil” and the
“bleeding air” procedures can be redone. Assemble
and repeat the pressurizing procedure. To test the
shock absorber for nitrogen gas leaks, submerge in
water.

! WARNING

Never have a nitrogen bottle in the area without having
it chained or secured. If the bottle should tip over and
the regulator break off, the gas inside it is under 1800
lb of pressure and personal injury may result.

! WARNING

Always rotate the regulator T-handle to its loose posi-
tion each time when finished using the system. Each
time before the nitrogen tank valve is opened, check to
make sure the regulator T-handle is turned out. When
opening the nitrogen tank valve, never stand in front
of the regulator in case there should be a problem.

Manual

Table of Contents

«
...
488
489
490
491
492
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды