Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 508

Страница: 508 / 535

8-18

1. Place the steering tie rod into position on the upper

arm of the steering shaft. Secure with the cap screw

(coated with green Loctite #609), washer, and new

lock nut. Tighten the lock nut to 30 ft-lb.

FC206

2. Place the steering tie rod into position on the steering

post. Secure with the cap screw coated with green

Loctite #609 and new lock nut. Tighten new lock nut

to 30 ft-lb.

FC205

Steering Tie Rod (Bearcat/

F-Series/T-Series/Z1)

REMOVING

1. On the Bearcat 570/F-Series/T-Series, remove the

springs securing the expansion chamber; then

remove the expansion chamber from the engine com-

partment. Account for the two gaskets and the rubber

exhaust bumper.

FS203A

2. On the Z1, remove the hood; then remove the

exhaust springs securing the exhaust pipe to the

mounting tab and exhaust manifold. Move the

exhaust pipe out of the way to gain access to the

close-off cover.



NOTE: On the turbo models, loosen the intercooler

hose clamps at the intake pipe and the turbocharger;
then carefully work the intercooler upward until it
releases from the rubber grommets.

3. On the Z1, remove the two cap screws (A) securing

the close-off cover to the front end; then remove the

cover and account for the exhaust pipe mounting tab

(B) from the right-side cap screw.

ZJ020A

4. Remove and discard the lock nut securing the steer-

ing tie rod to the steering post; then remove the cap

screw and lock nut securing the left-side inner tie rod

and steering tie rod to the drag link. Discard the lock

nut.

FS260A

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the ball joints for damaged threads or wear.

2. Inspect the tie rod for damage, unusual bends, or

wear.

INSTALLING

1. Thread the jam nuts onto the ball joints; then equally

thread the ball joints onto the steering tie rod.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 508 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: