Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 53 / 535

background image

2-15

2

Engine Removing/

Installing - CFR/M-Series

800/1000 - Crossfire 800

This engine sub-section has been organized to show a

progression for the removing/installing of the Arctic Cat

800/1000 cc (CFR/Crossfire/M-Series) engines. For con-

sistency purposes, this sub-section shows a complete and

thorough progression; however, for efficiency it may be

preferable to remove only those components needing to

be addressed. Also, some components may vary from

model to model. The technician should use discretion and

sound judgment.



NOTE: Critical torque specifications can be found in

Section 1 of this manual.



NOTE: Some illustrations and photographs used in

this section are used for clarity purposes only and
are not designed to depict actual conditions.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this engine

section.



NOTE: Special tools are available from the Arctic

Cat Service Parts Department.

Removing



NOTE: Prior to starting the removing procedure,

disconnect the hood harness and the air intake con-
nector from the air silencer; then remove the cables
and pins securing the hood to the front end, remove
the hood, and remove the access panels.



NOTE: At this point if the technician’s objective is to

service Top-Side Components, the engine does not
have to be removed from the chassis. Proceed to Ser-
vicing Top-Side Components.

1. Remove the belt guard and disconnect the exhaust

temperature sensor; then remove the cable ties secur-

ing the sensor harness to the chassis.



NOTE: For assembling purposes, note the location

of the cable ties securing the harness to the chassis.

2. Remove all springs and the hairpin clip securing the

expansion chamber and resonator; then remove these

components from the engine compartment.

3. Remove the three cap screws securing the heat shield

to the chassis and oil reservoir. Account for the heat

shield pad from the cap screw (A).

IO004B

4. Using Drive Clutch Bolt Tool, remove the cap screw

and high-collar washer securing the drive clutch to

the crankshaft.

5. Using the Drive Clutch Puller and an impact wrench

or a breaker bar and Drive Clutch Spanner Wrench,

tighten the puller. If the drive clutch will not release,

sharply strike the head of the puller. Repeat this step

until the clutch releases. Remove the drive clutch.

6. Remove the cap screw from the driven pulley and

slide the driven pulley off the gear case input shaft.

Account for alignment washers.

CM125A

7. Using a small needle-nose pliers, remove the servo-

motor retaining clip and the cable holder.

TZ069A

Description

p/n

Drive Clutch Bolt Tool

0644-281

Drive Clutch Puller

0744-062

Drive Clutch Spanner Wrench

0644-136

Driven Pulley Puller

0644-469

CAUTION

Never attempt to substitute any other drive clutch puller
for the recommended puller or severe clutch damage
will occur.

Manual

Table of Contents

«
...
51
52
53
54
55
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Lynx SHREDDER 3900 600R

Бренд: BRP Страницы: 268

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды