Arctic Cat Sno Pro 120 2011 страница 60 Скачать руководство пользователя | Manualshive

Страница: 60 / 535

background image

2-22

24. Check drive clutch/driven pulley alignment (see Sec-

tion 6). Install the drive belt. Check belt deflection.

Secure the belt guard (see Section 6).

25. Fill the cooling system (see Liquid Cooling System

in Section 3).

26. Install the resonator and secure with the hairpin clip

and springs; then place the expansion chamber and

grafoil gaskets into position and secure to the

exhaust manifold and resonator with the springs.



NOTE: When installing the four exhaust manifold

springs, the long hook portion of the spring must be
attached to the exhaust manifold or premature spring
failure will result.

27. Install and secure the access panels; then place the

hood into position on the front end and secure with

the two pins and the cables.

28. Connect the ignition harness to the ECU and the

hood harness to the main harness; then connect the

air intake connector.

CM038

29. With the heat shield pad in place, install the heat

shield and secure it to the chassis and oil tank with

the three cap screws; then tighten the two cap screws

to the oil tank to 26 in.-lb. Tighten the remaining cap

screw to 20 ft-lb.

30. Start the engine and warm up to operating tempera-

ture; then verify that all components are functioning

properly and that coolant is circulating through the

cooling system properly.

31. Allow the engine to cool; then check the coolant

level and add coolant as necessary. Verify the tight-

ening torque of the drive clutch.

32. Install the skid plate.

CAUTION

After running the engine to the proper operating temper-
ature, shut the engine off; then open the hood and
access panels and inspect for any signs of coolant, gas-
oline, or oil leakage.

CAUTION

Never run the engine with the hood harness discon-
nected or damage to the electrical system will result.

CAUTION

If the engine had a major overhaul or if any major com-
ponent was replaced, proper engine break-in proce-
dures must be followed (see Section 1). If the proper
engine break-in procedures are not followed, severe
engine damage may result.

Manual

Table of Contents

«
...
58
59
60
61
62
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

1987 Arctic Cat Super Jag

Бренд: CPC Страницы: 157

LYNX Radien 2019

Бренд: BRP Страницы: 229

Бренд: BOMBARDIER Страницы: 48

Бренд: BOMBARDIER Страницы: 50

Alpine 1984 Series

Бренд: BOMBARDIER Страницы: 54

formula mx 1987

Бренд: BOMBARDIER Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды