Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 61 / 535

2-23

Engine Removing/

Installing - F-Series 500/

600/800

This engine sub-section has been organized to show a

progression for the removing/installing of the Arctic Cat

500/600/800 cc (F-Series) engines. For consistency pur-

poses, this sub-section shows a complete and thorough

progression; however, for efficiency it may be preferable

to remove only those components needing to be

addressed. Also, some components may vary from model

to model. The technician should use discretion and sound

judgment.



NOTE: Critical torque specifications can be found in

Section 1 of this manual.



NOTE: Some illustrations and photographs used in

this section are used for clarity purposes only and
are not designed to depict actual conditions.

SPECIAL TOOLS

A number of special tools must be available to the techni-

cian when performing service procedures in this engine

section.



NOTE: Special tools are available from the Arctic

Cat Service Parts Department.

Removing

1. Remove the hood and the left-side and right-side

access panels; then remove the torx-head screws

securing the console.

0743-777

2. Lift the rear of the console and disconnect the con-

sole/main harness plug-in; then remove the console.

3. Remove the hairpin clip and all springs securing the

expansion chamber and resonator; then remove these

components from the engine compartment. Account

for the two exhaust gaskets.



NOTE: On the LXR, disconnect the negative cable

from the battery.

4. On the standard models, push down on both seat

retainer brackets (located in the rear storage com-

partment) and remove the seat.



NOTE: On the LXR and Sno Pro models with the

seat adjusted to its lowest position, remove the self-
tapping screw from the right-side seat adjustment
track; then remove the seat.

ZJ100A

5. Remove the torx-head screws securing the handlebar

close-off panel; then remove the panel.

6. Remove the lock nuts and torx-head cap screws (A)

securing the right-side front and rear spar panels;

then remove the torx-head screws (D) securing the

left-side rear spar panel to the gas tank and support

tube.

742-207A



NOTE: The right-side rear spar panel will remain

secured to the chassis.

7. Remove the cap screw located directly above the

ECU securing the air-silencer duct to the front upper

panel; then disconnect the air temperature sensor and

remove the duct.

Description

p/n

Drive Clutch Bolt Tool

0644-281

Drive Clutch Puller

0744-062

Drive Clutch Spanner Wrench

0644-136

Driven Pulley Puller

0644-469

CAUTION

Never attempt to substitute any other drive clutch puller
for the recommended puller or severe clutch damage
will occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды