Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 189

Страница: 189 / 535

3-10

3. Remove the separator tank breather hose to gain

access to the water pump; then remove the water

inlet hose from the water pump.

ZJ113A

4. Remove the two cap screws securing the water pump

to the engine; then remove the pump and account for

the O-ring.

ZJ114A

DISASSEMBLING

0742-104

1. Secure the water pump in a suitable support device;

then remove the two Phillips-head screws (A) secur-

ing the inner/outer pump housings.

2. Separate the inner/outer pump housings; then

remove the E-clip (B) from the impeller shaft,

remove the shaft from the inner housing, and remove

the ceramic seal (C) from the shaft.

3. With the inner housing secured in a suitable clamp-

ing device and using Blind-Hole Bearing Puller,

remove the mechanical seal (D); then remove the oil

seal (E).



NOTE: Apply heat to the housing to aid in removing

the seals.

4. Using the bearing puller, remove the bearing (F)

from the inner housing.



NOTE: Apply heat to the housing to aid in removing

the bearing.

5. Clean the inner and outer housings with parts-clean-

ing solvent; then dry with compressed air.

ASSEMBLING

0742-104



NOTE: For this procedure, use Water Pump Bearing

and Seal Tool Kit.

1. Using the appropriate-sized installation tool, install

the bearing (F) into the inner housing.

2. Using the appropriate-sized installation tool, install

the oil seal (E) with the spring side of the seal facing

the bearing.

3. Place the mechanical seal (D) into the inner housing;

then using the appropriate-sized installation tool,

drive the seal into the housing until the lip of the seal

is properly seated.

4. Install the ceramic seal (C) onto the impeller shaft

with the ceramic face of the seal facing away from

the impeller.

5. Install the impeller shaft into the inner housing and

secure with the E-clip (B); then with a new O-ring

properly positioned in the outer housing, place the

water pump halves together.

CAUTION

Care should be taken not to apply too much heat to
the housing or the bushing next to the bearing may be
damaged.

CAUTION

Care should be taken not to apply too much heat to
the housing or the bushing next to the bearing may be
damaged.

! WARNING

Always wear safety glasses when drying components
with compressed air.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 189 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: