Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 148

Страница: 148 / 535

2-110

ZJ028B

8. On the non-turbo models, remove the cap screws

securing the two intake flanges to the cylinder head;

then remove the flanges.

ZJ029A

9. On the turbo models, remove the four cap screws

securing the manifold adapter assembly; then

remove the manifold.

TZ087A

10. Remove the three cap screws securing the thermostat

cap to the engine; then remove the cap and thermo-

stat and account for the harness bracket from the

lower cap screw.

ZJ030A



NOTE: Note the position of the thermostat bypass/

check valve for assembling purposes.

ZJ091A



NOTE: If engine case cleaning or replacing is nec-

essary, remove the coolant and oil sensors from the
engine case.

ZJ031A

11. Remove the eighteen cap screws securing the mag-

neto cover to the engine; then remove the cover and

account for the starter idler gears, idler pins, spacers,

dowel pins, and the oil pump seal.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 148 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: