Arctic Cat Sno Pro 120 2011 страница 196 Скачать руководство пользователя | Manualshive

Страница: 196 / 535

background image

3-17

3

11. With a light film of engine oil applied to the tappets,

install the correct shim (A) and tappet (B) to each

valve being adjusted.

ZJ083A



NOTE: Prior to installing the camshaft, apply

engine-assembling grease to the camshaft journals
and lobes.

12. With the crankshaft rotated to the top-dead-center

position, place the cam chain over the sprocket of the

exhaust camshaft.



NOTE: The exhaust camshaft must be installed first.



NOTE: When installing the cam chain to the gear of

the exhaust camshaft, position the chain so no slack
between the crankshaft gear and exhaust camshaft
exists when the camshaft is installed. All slack in cam
chain must be on the side of the tension adjuster.

ZJ084

13. With the timing marks (A) on the face of the exhaust

camshaft gear properly aligned, place the camshaft

into position on the cylinder head.

0741-801

14. With the cam chain properly seated to the gears of

the crankshaft and exhaust camshaft, install the

intake camshaft noting that the timing marks (B) are

properly aligned.



NOTE: With the camshafts and cam chain in place,

there should be exactly 16 pins from intake cam mark
3 to exhaust cam mark 2.

741-780A

15. Install the cam chain tensioner adjuster by first com-

pressing the locking clip; then by pushing in the ten-

sioner shaft until completely compressed.

ZJ085A

16. Install the tensioner and secure with two Allen-head

cap screws (B); then tighten to 84 in.-lb. Install the

ball, spring, and tensioner bolt (A) and tighten to 18

ft-lb.

Manual

Table of Contents

«
...
194
195
196
197
198
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды