manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

1-7

1

Preparation After 

Storage

Taking the snowmobile out of storage and correctly pre-

paring it for another season will assure many miles and

hours of trouble-free snowmobiling. Arctic Cat recom-

mends the following procedure:

1. Clean the snowmobile thoroughly. Polish the exte-

rior of the snowmobile.

2. Clean the engine. Remove the cloth from the exhaust

system. Check exhaust system and air silencer for

obstructions. On the turbo models, inspect the air fil-

ter and replace as necessary.

3. Inspect all control wires and cables for signs of wear

or fraying. Replace if necessary. Use cable ties or

tape to route wires and cables away from hot or rotat-

ing parts.

4. Remove and inspect the drive belt for cracks and

tears. Check belt specifications. Replace if damaged

or worn. Install the drive belt (see Section 6).

NOTE: If the old belt is worn but in reasonable con-

dition, retain it with the snowmobile as a spare in
case of emergency.

5. On the 570 cc, inspect the in-line fuel filter and

replace if necessary; then adjust the carburetors and

choke cable.

6. Inspect all fuel hoses and oil hoses for deterioration

or cracks; replace if necessary. Make sure all connec-

tions are tight. 

7. On the 2-stroke models, fill the oil-injection reser-

voir with the recommended injection oil; then

inspect each spark plug. Replace, gap, or clean as

necessary.

NOTE: On the 2-stroke models after prolonged stor-

age, Arctic Cat recommends one tankful of 100:1 gas/
oil mixture be used in conjunction with the oil-injec-
tion system to ensure proper lubrication.

8. Adjust the throttle cable.

9. Tighten all nuts, bolts, and cap screws making sure

all calibrated nuts, bolts, and cap screws are tight-

ened to specifications.

10. If not done during preparation for storage, lubricate

all grease fittings (front and rear suspension, spin-

dles, and upper steering shafts on the Crossfire/M-

Series or steering arms on the Bearcat/F-Series/Z1/T-

Series) with an all-temperature grease.

11. On liquid cooled models, check the coolant level and

all coolant hoses and connections for deterioration or

cracks. Add properly mixed coolant as necessary.

12. On fan cooled models, clean the engine cooling fins

and all shrouding.

13. On electric start models, charge the battery; then

connect the battery cables making sure to connect the

positive cable first. Test the electric start system.

14. Inspect the entire brake system, all controls, head-

light, taillight, brakelight, ski wear bars, and head-

light aim; adjust or replace as necessary.

15. Adjust the track to the proper tension and alignment.

Lock the jam nuts.

16. Fill the gas tank with fresh, clean gas.

After Break-In Checkup 

(100 Miles - 2-Stroke/600 

Miles - 4-Stroke)

Certain areas require adjustment after the break-in period

in order to obtain peak performance. These areas are the

following.

CARBURETOR JETTING (570 cc) 

— Altitude, tem-

perature, and the use of oxygenated gasoline affect the

carburetion needed for optimum engine performance.

The carburetor main jets must be changed in conjunction

with changes in operating altitude, oxygenated gasoline

usage, and temperature.

DRIVE BELT DEFLECTION

 — Drive belt deflection

is very important to the snowmobile. Even if it is checked

and is correct when the snowmobile is set up, it does

change (more so during the break-in period). This is

because the rubber engine mounts and the rubber snubber

on the torque link will all take a “set” during the first 100

miles allowing the distance between the drive clutch and

driven pulley to shorten. When this happens, the snow-

mobile will appear to have a too long drive belt. To add

to this, the drive belt itself wears and stretches somewhat

leading to a low-end performance problem and, if not

corrected, causes premature drive belt wear.

After the break-in period, drive belt deflection should be

checked according to the instructions given in Section 6

of this manual.

DRIVE BELT BREAK-IN

 — Drive belts require a

break-in period of approximately 25 miles. Drive the

snowmobile for 25 miles at 3/4 throttle or less. By rev-

ving the engine up and down (but not exceeding 60 mph),

the exposed cord on the side of a new belt will be worn

down. This will allow the drive belt to gain its optimum

flexibility and will extend drive belt life.

CAUTION

On the 570 cc if the gas in each carburetor float cham-
ber was not drained prior to storage, the carburetors
must be cleaned before starting the engine.

! WARNING

Be sure to tighten the swivel adapter jam nuts securely.
If a jam nut isn’t tightened, the adjuster can rotate out of
the carburetor cap causing the piston valve not to
return to the full-closed position.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Загрузить еще бренды