Arctic Cat Sno Pro 120 2011 страница 399 Скачать руководство пользователя

Страница: 399 / 535

7-31

6. Tip the snowmobile onto the other side; then align

the rear arm assembly with the appropriate hole in

the tunnel. Secure the pivot arm assembly with a cap

screw, lock washer, and flat washer. TIGHTEN

ONLY UNTIL SNUG.



NOTE: Do not install the short legs of the rear

springs onto the adjusting cams at this time.

7. At this time, place the snowmobile to the upright

position; then tighten both rear arm mounting cap

screws to 40 ft-lb.



NOTE: At this point, tighten all remaining skid

frame mounting hardware to 40 ft-lb.

8. Using the Rear Suspension Spring Tool, install the

short legs of the rear springs onto the adjusting cams

making sure the cams are in the same adjustment

positions.

9. Adjust track tension and alignment (see Track Ten-

sion and Track Alignment in Section 6).

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды