manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Сервисный мануал Arctic Cat Sno Pro 120 2011 доступен для бесплатного скачивания на {вашем сайте}. Этот руководство поможет вам поддерживать и обслуживать ваш снегоход, обеспечивая надежную работу. Скачайте его прямо сейчас и получите всю необходимую информацию для правильного ухода за вашим транспортным средством.

Поделиться
Скачать
background image

5

5-23

ZJ142A

CLEANING AND INSPECTING

NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Thoroughly clean all components except the arma-

ture and brushes in parts-cleaning solvent; then dry

with compressed air.

2. Inspect all threaded areas for damaged or stripped

threads.

3. Inspect the brush holder assembly and brushes for

damage or wear. Using a caliper, measure the length

of the brushes. If brush measurement is less than

0.40 in., replace with new brushes and brush springs

as a set.

4. Inspect brush leads for cracks, wear, or fraying. If

any of these conditions exist, replace with new

brushes along with new brush springs as a set.

5. Inspect the rear cover bushing for wear. 

6. Inspect the front cover bearing for wear.

7. Inspect the brass commutator end of the armature for

any discolored spots or damage. If the commutator is

slightly discolored or damaged, the armature must be

replaced. This is a molded commutator and no

attempt to turn it down in a lathe should be

attempted.

8. Inspect the commutator end of the armature for

buildup in the grooves. Carefully remove any

buildup by undercutting using a thinly ground hack-

saw blade. Do not cut any deeper than the original

groove which can be seen by looking at the end of

the commutator.

9. Using a caliper, measure the undercut. Maximum

undercut groove must be 0.008 in.

SNO2171

10. Inspect the commutator for shorting using a multim-

eter and the following procedure.

A. Set the selector to the OHMS position.

B. Touch the black lead to the armature shaft.

C. Using the red tester lead, probe the commutator

end of the armature. The meter indicator should

not change. If the indicator shows resistance, the

armature is shorted and must be replaced.

11. Inspect the armature for shorting using a “growler”

and the following procedure.

A. Place the armature in the “growler.”

B. While holding a metal strip on the armature,

rotate the armature an entire revolution. If the

metal strip vibrates at any point on the armature,

the armature is shorted and must be replaced.

0725-653

12. Inspect the ground brushes to make sure they are

properly grounded. Use a multimeter and the follow-

ing procedure.

A. Set the selector to the OHMS position.

B. Touch the black tester lead to a ground brush.

C. Touch the red tester lead to the brush holder

assembly.

CAUTION

Do not wash the armature and brushes in any kind of
solvent. Use only compressed air and clean dry, lint-
free cloth in cleaning these components.

CAUTION

Do not use emery cloth to clean the commutator as
emery particles will become imbedded in the brass
commutator resulting in a short circuit. Use only #200
grit sandpaper.

CAUTION

Buildup in the grooves must be removed to prevent
any chance of an electrical arc between individual sec-
tions of the commutator.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Yamaha SRX 120 2017 Operator'S Manual preview
SRX 120 2017
Бренд: Yamaha Страницы: 30

Бренды по названию

Популярные бренды

Загрузить еще бренды