Arctic Cat Sno Pro 120 2011 страница 453 Скачать руководство пользователя

Страница: 453 / 535

7-85

2. With the slide rail assembly on its side, place the rail

that was removed or replaced into position; then

push the rear arm cap screw and the pivot shock axle

cap screw through the mounting holes in the rail.

3. Install the lock nuts securing the front shock axle (A)

and rear arm assembly (B) to the slide rails. Tighten

only until snug.

FZ083B

FZ084B

4. Secure the front arm to the slide rail with the cap

screws and lock nuts. Tighten to 40 ft-lb.

FZ070



NOTE: At this point, return to steps 2 and 3 and

tighten the rear arm and front arm cap screws and
lock nuts to 40 ft-lb.

5. Install the adjuster bushing and rear idler wheel.

Install a cap screw and flat washer. Tighten only until

snug.

FZ066



NOTE: Care must be taken that the adjuster bushing

slot with the hole is aligned properly with the adjuster
bolt.

CM261A



NOTE: Tighten the rear idler wheel axle only until

snug until the skid frame has been installed and track
tension has been adjusted; then the axle assembly
must be tightened to 20 ft-lb.

6. Install coupler block w/bushing. Secure with cap

screw. Tighten securely.

FZ076

7. Install the rear arm limiter and secure with the cap

screw. Tighten the cap screw to 50 ft-lb.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды