Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 125

Страница: 125 / 535

2-87

16. Start the remaining cap screws being very careful not

to move the cylinder head. ONLY FINGER-

TIGHTEN AT THIS TIME; then tighten the cap

screws in two steps to 25 ft-lb using the appropriate

pattern shown.

0742-200

0742-199

17. On the 800 cc, install the spark plugs and on both

models, tighten the spark plugs to 19 ft-lb; then

install the spark plug wires.



NOTE: On the 800 cc, connect the knock sensor

plug-in.



NOTE: If the knock sensor was removed or

replaced, it must be tightened to 17 ft-lb and secured
with a new lock plate.

18. Install the APV gaskets into position as noted during

disassembly; then with the raised edge (A) of the

bottom of the valve aligned with the channel (B) of

the cylinder, install the APV’s onto the cylinder and

secure with the cap screws. Tighten to 96 in.-lb.

CM147A

19. Install the side-plate brace; then secure with the cap

screws (coated with blue Loctite #243).



NOTE: Install the two front lower cap screws first to

properly align the remaining cap screws.

CM133B



NOTE: At this point if no additional engine service

work is necessary, proceed to Engine Installing - step
26.

Cleaning and Inspecting



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

CYLINDER HEAD

1. Using a non-metallic carbon removal tool, remove

any carbon buildup from the combustion chambers

being careful not to nick, scrape, or damage the com-

bustion chambers or the sealing surfaces.

2. Inspect the spark-plug holes for any damaged

threads.

3. Inspect the cylinder head for flatness using a

straightedge and a feeler gauge. Acceptable warpage

must not exceed 0.002 in.



NOTE: If the warpage exceeds specification, resur-

face the cylinder head using procedures identified in
step 4.

FS270

800 cc

1000 cc

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 125 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: