Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 274

Страница: 274 / 535

5-13

SERVICE ICON

The Service Icon is controlled by the CCU/ECU and may

illuminate for a number of reasons. The icon should illu-

minate each time the engine is started, and it should go

out after a few seconds. If the icon stays illuminated

while the engine is running, the CCU/ECU is receiving

input that is outside of its established parameters.

FZ001D

FZ003B



NOTE: If the icon illuminates while the engine is

running, the CCU is receiving input that is outside of
its established parameters.

Accessing CCU Codes

1. Connect the appropriate harness from CCU Diagnos-

tic Test Kit to the diagnostic port.

2. Start the engine.

3. After approximately 5 seconds, the service icon on

the gauge will begin flashing.

4. The readout screen will display an error code as

CCU followed by a number. When all error codes

have been output, the service icon flashes twice

quickly.



NOTE: Refer to the CCU Diagnostic Codes chart for

descriptions.

Clearing Fault Codes

1. Connect the appropriate harness from CCU Diagnos-

tic Test Kit to the diagnostic port.

2. Start the engine.

3. Press and hold the shift button for 5 seconds.



NOTE: Two quick flashes of the service icon indi-

cate the codes have been cleared.

VOLTAGE TEST



NOTE: The following test should be made using

MaxiClips and the Fluke Model 77 Multimeter set to
the DC Volt scale.



NOTE: The CCU tests were made with the connec-

tors plugged in, spark plugs removed and grounded,
and by pulling the recoil starter rope briskly.

LOW POWER

1. Connect the red maxiclip and meter lead to the red/

blue lead of the connector; then connect the black

maxiclip and meter lead to the black lead of the con-

nector.

2. Pull the recoil starter rope briskly.

3. Meter reading must be within specification.



NOTE: Repeat test three times to confirm results.

Deluxe Gauge

Standard Gauge

CCU Diagnostic Codes

Code

Trouble

Cause

CCU 32 High power DC

output over current.

Headlight and Hand Warmer (Red/
Black) circuit current greater than 20
Amps.

CCU 33 High power DC

output shorted.

Headlight and Hand Warmer (Red/
Black) circuit shorted to ground.

CCU 34 Low power DC

output over current.

Gauge, Taillight, and APV Servo
Power (Red/Blue) circuit current
greater than 20 Amps.

CCU 35 Low power DC output

shorted.

Gauge, Taillight, and APV Servo
Power (Red/Blue) circuit shorted to
ground.

CCU 37 System over voltage. Spike in battery voltage - excessive

gear case shifting.

CCU 38 Gear shift actuator

failure.

Wires to reverse actuator damaged or
shorted to ground.

CCU 42 Tachometer input

failure (engine
running - no
tachometer signal
present).

Tachometer signal wire shorted to
ground.

CCU 43 Gear position switch

failure.

Gear position switch damaged or
unplugged - reverse actuator not
working correctly.

CCU 44 CCU over

temperature.

Internal CCU temperature over 105° C
(221° F).

! WARNING

Most voltages generated by the ignition system are
sufficient to interrupt pacemakers! All technicians,
especially those using pacemakers, must avoid con-
tact with all electrical connections after the engine has
been started.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 274 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: