Arctic Cat Sno Pro 120 2011 страница 437 Скачать руководство пользователя | Manualshive

Страница: 437 / 535

background image

7-69

7

CM222A

12. Install the skid frame (see Installing Skid Frame in

this sub-section).

Installing Skid Frame

1. Using a suitable handlebar support stand, tip the

snowmobile onto one side.

2. Pull the track away from the tunnel and spread open;

then place the skid frame into the track.

3. Position the front of the skid frame into the tunnel

and align the front arm with axle to the appropriate

mounting hole in the tunnel. Insert the cap screw and

secure with washer and lock nut through the tunnel

mounting hole and through the front arm. DO NOT

TIGHTEN AT THIS TIME. Repeat this procedure

on the other side.

739-992A



NOTE: To aid in centering the front arm with the

hole in the tunnel, position the skid frame and track
at a 45° angle to the bottom of the tunnel.

4. Elevate the rear of the skid frame and the track into

position in the tunnel.

5. Align the rear arm assembly with the appropriate

hole in the tunnel. Secure the rear arm assembly with

a cap screw (coated with red Loctite #271), lock

washer, and flat washer. DO NOT TIGHTEN AT

THIS TIME.



NOTE: Do not install the short legs of the rear

springs onto the adjusting cams at this time.

6. At this time, tighten the rear arm assembly cap

screws to 40 ft-lb; then tighten the front arm with cap

screws, flat washers, and lock nuts to 40 ft-lb.

7. Using the Rear Suspension Spring Tool, install the

short legs of the rear springs onto the adjusting cams

making sure the cams are in the same adjustment

positions.

8. Adjust track tension deflection and alignment (see

Track Tension and Track Alignment in Section 6).

CAUTION

When installing the skid frame, make sure the rear arm
shock mounting location on the pivot/axle is posi-
tioned correctly above the axle or component damage
will occur.

Manual

Table of Contents

«
...
435
436
437
438
439
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды