Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 172 / 535

2-134

FZ021

32. Secure the driven pulley with components and hard-

ware as noted in removing. Tighten to 32 ft-lb.

FZ019

33. Check drive clutch/driven pulley alignment.

34. Install the drive belt (so the part number can be

read); then install the belt guard.

35. Install the battery; then secure with the hold-down

plate. Connect the positive cable and then the nega-

tive cable.

36. With all coolant hoses installed and secured as noted

during disassembling, loosen the bleed screw and

add coolant into the filler neck until coolant is visible

at the bleed screw; then tighten the bleed screw and

add coolant to the coolant reservoir Full-Cold line.

744-032A

37. If the engine oil was drained, remove the filler cap

from the oil reservoir and add the recommended

amount of oil using the following procedure. If the

engine oil was not drained, start the engine and allow

it to run for 5 minutes. Inspect for any signs of cool-

ant leaks; then proceed to step 38.

A. Pour 2.9 l (3 U.S. qt) of the recommended engine

oil into the oil reservoir.

B. Open the air bleed bolt located on the oil pump

(beneath the coolant tank) to purge air from the oil

hose.

ZJ004A



NOTE: When air can no longer be heard purging

from oil pump bleed, tighten the bleed bolt to 7.5 ft-lb.

C. Without starting the engine, place the handlebar

emergency stop switch to the RUN position and

the ignition switch to the ON position. The Oil

Pressure Warning Light should illuminate.

D. If the warning light illuminates (from step C),

start the engine. The warning light should go out

within five seconds. If it does, proceed to step E.



NOTE: If the warning light does not go out, shut the

engine off immediately and repeat step B; then place
the ignition switch to the ON position and repeat step
D.

E. Shut the engine off and pour the remaining

amount (0.9 1 or 1 U.S. qt) of recommended oil

into the oil reservoir; then proceed to check

engine oil level.

F. Start the engine and allow it to warm up for 5-10

minutes.

CAUTION

Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur.

CAUTION

Do not apply Loctite to the cap screw or damage to the
gear case will occur.

! WARNING

Never run the engine without the belt guard secured.

! WARNING

Battery acid is harmful if it contacts eyes, skin, or
clothing. Care must be taken whenever handling a bat-
tery.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды