Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 383 / 535

7-15

5. Inspect the spring, spring slide, sleeve, washers, slide

block insert, and shaft area for wear.

6. Inspect the adjusting cams and arms for cracks.

INSTALLING

1. Slide the sleeve and spring onto the idler arm.

MS069

2. Place the slide spacer and slide block (with spring in

slide block) into position on the slide rail. Secure

with a cap screw, three flat washers, and lock nut.

Tighten to 20 ft-lb.



NOTE: Make sure the spring is located above the

spring slide mounting cap screw.

SC017

MS068

3. Using a suitable driving tool, install the rear upper

idler wheel on the idler arm.

SC018

4. Install the two pivot arm spacers onto the idler arm.

MS064

5. Place the flared bushings with a thin flat washer

through the back side of the pivot arm assembly.



NOTE: If the flared bushing in the pivot arm is

loose, it must be cleaned and green Loctite #609
must be applied to it prior to installation.

6. Align the marks on the idler arm to the centerline of

the pivot arm assembly; then install the pivot arm

with the flared side of the bushing out. Secure the

pivot arm to the idler arm with cap screws and lock

nuts. Tighten to 20 ft-lb.

SC014A



NOTE: When tightening the pivot arm lock nuts,

tighten the lower lock nut first or binding may occur.

CAUTION

When driving the idler wheel onto the idler arm, use a
tool to contact the inside race of the bearing or dam-
age to the wheel or bearing may occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды