Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 489 / 535

background image

7-121

7



NOTE: At this point, DO NOT attempt to pull the

shaft up out of the body.

17. If there is any interference while pushing the shaft

into the body, the IFP is in the wrong location.

18. If there is no interference, proceed to step 19.

19. Maintain the shock in the vise.

20. Make sure the nitrogen valve is directed outward.

21. Insert the needle squarely into the center of the nitro-

gen valve (taking care that the valve is directed away

from face and body) and pressurize the reservoir to

200 psi. The shock shaft should be fully extended

from the pressure before the final pressure reading is

taken. Continue charging while pulling the reservoir

away from the needle using a smooth, straight motion.

Keep the reservoir as straight as possible to prevent

the needle from bending. As the reservoir and needle

separate, a “popping” sound should be heard.

FS016

22. Install the button-head screw into the nitrogen valve.

FS040

23. Clean all oil residue from the shock and reservoir

with solvent and dry with compressed air in a well

ventilated area.

24. Install the polyurethane bushings and steel sleeves

into the eyelets.

Shaft Eyelet

REMOVING

1. Using Gas Shock Rod/Body Clamping Tool to pre-

vent damage to the shaft surface, place the shock

shaft into a vise.

2. Heat the shaft eyelet with a torch to soften the Loc-

tite.

AG260



NOTE: The eyelet must be heated up to 300° for the

Loctite to soften.

3. Using a wrench, unscrew the eyelet from the shaft.

! WARNING

If there is interference, unthread the bearing assembly
from the body and repeat steps 4-16 of Assembling.
Failure to repeat the steps and rid the shock of the
interference may cause damage to the shock resulting
in improper shock performance and could cause oper-
ator injury.

! WARNING

Charge the shock using nitrogen gas only. DO NOT
CHARGE WITH ANY OTHER TYPE OF GAS. Doing so
will compromise the performance of the shock and
may be EXTREMELY DANGEROUS.

Manual

Table of Contents

«
...
487
488
489
490
491
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренд: Polaris Страницы: 5

Бренд: Polaris Страницы: 56

Бренд: Polaris Страницы: 99

Бренд: Polaris Страницы: 137

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды