Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 363 / 535

background image

6-40

ZJ244



NOTE: For aid in installing the outer bearing,

insert a length of shaft (the same diameter as the
bearing inner bore) through the inner bearing, drive-
shaft sleeves, and outer bearing to maintain proper
alignment of the driveshaft sleeves for driveshaft
installation.

ZJ242

ZJ243

7. Apply Anti-Seize Thread Compound to the splines

of the brake disc; then with the brake caliper spacer

properly installed, slide the caliper onto the drive-

shaft far enough to install the spacer and brake disc.

ZJ232

ZJ233

8. With the brake disc splines and driveshaft splines

aligned, use a soft hammer and tap the caliper from

side to side until the caliper is properly seated to the

tunnel.

9. Install the Phillips-head cap screw and lock nut (B);

then install the four lock nuts (A). Tighten to 20 ft-lb.

740-188A

10. Apply Anti-Seize Thread Compound to the threads

of the brake disc retaining nut; then install the nut.



NOTE: At this point, tighten the retaining nut only

until snug.



NOTE: If the outer caliper housing was removed

during disassembling, install a new O-ring and place
the housing into position; then secure with the two
Allen-head cap screws. Tighten to 17 ft-lb.



NOTE: Always use a new O-ring and make sure the

O-ring is properly seated in the outer brake housing.

CAUTION

When installing a bearing, always press on the outer
race of the bearing.

Manual

Table of Contents

«
...
361
362
363
364
365
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды