Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 19 / 535

background image

1-17

1

Electrical Specifications

1100 cc



NOTE: The ignition system is a Normally Closed Ignition.

* Main harness plugged in



NOTE: To test the coolant temperature sensor, see Section 5.

These tests were made at room temperature with the MaxiClips (p/n 0744-041), Fluke Model 77 Multimeter (p/n

0644-559), and the Peak Voltage Reading Adapter (p/n 0644-307). For ignition coil peak voltage test, the battery

must be fully charged. Also, the main harness connectors must be unplugged (except on the voltage regulator/recti-

fier test).

Description

Resistance Test

Test Value

+ Test Connections -

Magneto Coil (three tests)

0.2-0.4 ohm

yellow

yellow

Coil (1)

1.4 ohms

red/green

gray/green

Coil (2)

1.4 ohms

red/green

brown/green

Crankshaft Position Sensor

173-211 ohms

blue/white

green/white

Coolant Temperature Sensor

2.3k-2.6k ohms

yellow/black

ground

Injection Coil Starter Relay

3.6 ohms

black/yellow

black

Spark-Plug Cap

4000-6000 ohms

cap end

cap end

Description

Test Value

+ Test Connections -

Voltage Regulator/Rectifier*

12-14.5 DC Volts

terminal

terminal

Magneto Coil (no load) (three tests)

36-44 AC Volts

yellow

yellow

Description

Peak Voltage Test

+ Test Connections -

Coil (1)

5.0 DC Volts

red/green

gray/green

Coil (2)

5.0 DC Volts

red/green

brown/green

! WARNING

Most voltages generated by the ignition system are sufficient to interrupt pacemakers! All technicians, especially
those using pacemakers, must avoid contact with all electrical connections when pulling the recoil starter rope or
after the engine has been started.

Manual

Table of Contents

«
...
17
18
19
20
21
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

800 PRO-RMK 2011

Бренд: Polaris Страницы: 128

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды