Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 170 / 535

2-132

TZ075A

17. Connect the harness plug-ins to the ignition coils (A)

and camshaft sensor (B); then route the main harness

to the proper connector locations and secure with

cable ties as noted during removing.

ZJ094A

18. On the turbo models, install the spark plug wires and

the throttle cable to the throttle body pulley and

bracket; then tighten the jam nuts securely.

19. On the non-turbo models, install the air silencer (see

Section 3); then on all models, install the gas tank

(see Section 8).

20. Connect the fuel pump four-wire connectors (A);

then connect the harness plug-in (B) to the regulator/

rectifier.

ZJ011C

21. With the harness connected, install the air pressure

sensor to the bracket on the right-side upper frame.

22. Install the close-off cover to the front end with the

two cap screws (A) noting the mounting tab (non-

turbo only) (B) is installed with the right-side cap

screw. Tighten cap screws securely.

ZJ020A



NOTE: On the Bearcat Z1 XT, install the close-off

panel; then with the mounting tab (A) on the left front
cap screw, secure the panel with the four cap screws.

TZ078A

23. Place the resonator into position in the chassis and

install the two springs securing the resonator to the

chassis; then install the exhaust pipe and secure to

the manifold and resonator with six springs.



NOTE: On the non-turbo models, secure the resonator

to the upper frame with the tab washer and hairpin clip.

24. Connect the harness plug-in for the oxygen sensor.



NOTE: Steps 25-28 are for the turbo models only.

25. Install the upper heat shield; then connect the coolant

return hose to the turbo and secure with the hose clamp.

CAUTION

Make sure the harness is routed away from the exhaust
or any moving parts.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды