manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 234 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 234

4-8

AH137

10. Place the E-clip into position on the jet needle. From

the bottom of the jet needle, slide the E-clip washer

up against the E-clip. Place the jet needle into the

piston valve.

NOTE: Place the E-clip in the proper position as

noted in disassembly.

725-266C

11. Place the cable retainer into the piston valve and

secure with the Phillips-head screw. Guide the cable

end down into the cable retainer slot and slide the

cable end to the center of the piston valve. Release

the spring and retainer plate to lock the cable in posi-

tion.

AH075

NOTE: The round part of the cable end must come

through the hole in the plate/piston valve. If it
doesn’t, the cable isn’t assembled to the piston valve
correctly.

12. Thread the plunger cap onto the choke cable. Place

the spring over the cable end and compress. Position

the cable end into the starter plunger and release the

spring.

INSTALLING

1. Place the piston valve into position making sure the

full-length groove in the piston valve is aligned with

the pin in the mixing chamber bore; then thread the

mixing body top onto the carburetor and tighten

securely.

CM056A

NOTE: Prior to threading the mixing body top onto

the carburetor, assure the rubber washer is posi-
tioned correctly on the body top.

2. Making sure the mixing body top plate is properly

positioned, secure the mixing body top by tightening

the screw and lock washer.

3. Connect the fuel hose to the carburetor inlet fitting;

then using Fuel Hose Clamp Tool, secure the hoses

to the carburetor with the clamps.

4. Place the carburetor into position in the flange and

air silencer boot; then tighten the flange clamp mak-

ing sure the carburetor is level. Do not over-tighten

the flange clamp as it will damage the carburetor

flange.

TZ102A

NOTE: Slide the carburetor into the air silencer

boot; then slide the carburetor into the flange.

CAUTION

When installing the carburetors, make sure the gasline
hoses are properly routed to avoid premature wear
and/or contact with exhaust components.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов