Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 397 / 535

7-29

SC037A



NOTE: If the rear idler wheel was removed from the

opposite side slide rail, install the idler wheel and
secure it to the mounting block with cap screw,
washer, and lock nut. Tighten to 20 ft-lb.

SC038A

13. Install the skid frame (see Installing Skid Frame in

this sub-section).



NOTE: Install the rear arm springs onto the adjuster

blocks after the skid frame has been installed.

Articulating Skid Frame



NOTE: For the following procedure, refer to illustra-

tion 744-166A on the following page.

DISASSEMBLING

1. Remove the rear idler wheel cap screw (A), washer,

and lock nut from the cap screw side of the skid

frame.

2. Remove the two cap screws (B) and lock nuts secur-

ing the articulating skid frame to the slide rail.

3. With the adjuster rod axle (C) in place in the adjuster

rods (D), remove the lock nuts (E) from the adjuster

springs (F); then remove the adjuster rods and axle

from the swing arm.

4. Remove the two cap screws (G) securing the rear

axle/idler wheel assembly to the swing arm; then

remove the idler wheels and account for the two

adjuster bushings (H).

5. From one side, slide the rear axle (I) out from

between the swing arm and account for the two idler

wheel spacers (J) and two washers (K).

6. Remove the two cap screws and lock nuts (L) secur-

ing the adjuster blocks (M) to the swing arm.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect each idler wheel and plastic hub for cracks or

damage.

2. Rotate the idler wheel bearings (by hand) and inspect

for binding or roughness.

3. Inspect all bushings for wear or damage.

4. Inspect all weldments and the tubing of the arms and

spacers for cracks or unusual bends.

5. Inspect the track bumper guides for wear.

6. Inspect the axle surfaces for any signs of corrosion.

If corrosion is found, lightly buff the surface of the

axle with #400 wet-or-dry sandpaper; then apply a

light coat of grease.

ASSEMBLING

1. Install the adjuster blocks (M) into the swing arm;

then thread the two cap screws with lock nuts (L)

into the blocks.

2. Slide the rear axle through one side of the swing arm

and through a washer (K) and an idler wheel spacer

(J); then in order on the rear axle (I), install the cen-

ter idler wheel, the remaining spacer (J), and washer

(K). Continue to slide the rear axle through the other

side of the swing arm.

3. Slide an adjuster bushing (H) on each end of the rear

axle making sure the bushings are properly posi-

tioned to the adjuster bolts; then secure each rear

axle idler wheel with a cap screw (G). Tighten only

until snug.

4. Install the adjuster rods (D) into the swing arm; then

install the adjuster springs (F) and lock nuts (E).

Tighten only until snug.

5. Slide the adjuster rod axle (C) into the adjuster rods;

then install the swing arm axle into the swing arm.

6. Position the articulating skid frame between the slide

rails; then with the adjuster rod axle (C) and the

swing arm axle centered to the mounting holes of the

slide rails, install the cap screws (B) securing the

articulating skid frame to the slide rails.

7. Install new lock nuts to the cap screws (B) and

tighten to 20 ft-lb.

8. Install the rear idler wheel to the mounting block of

the slide rail. Secure with cap screw (A), flat washer,

and lock nut. Tighten to 20 ft-lb.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды