Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 183 / 535

3-4

FC127

4. Using a pair of snap ring pliers, install the snap ring

securing the inner seal in the crankcase.

FC128

5. Using the seal driver, carefully install the outer water

pump mechanical seal. Gently tap the seal down into

position until it seats itself against its flange.

FC129

6. Apply a light coat of grease to the sealing surface of

the oil-injection pump driveshaft; then install Oil

Seal Protector Tool at the end of the shaft. Twist the

shaft while pushing it through the oil and water

pump seals; then remove the tool.

FS233A

7. Position the shim on the oil pump end of the shaft;

then with the O-ring installed on the retainer, install

the oil-injection pump retainer.

FC130A



NOTE: For assembling purposes, always use new

O-rings lubricated with oil on the oil injection pump
and retainer.

8. With the O-ring in place on the oil-injection pump,

align the pump with the shaft; then install the pump.

Secure with two cap screws (coated with blue Loctite

#243). Tighten the two cap screws to 96 in.-lb.

FC131A



NOTE: After the oil pump has been secured, assure

that the oil hoses from the pump and intake flanges
are routed properly.

9. Place the lower check valve into position; then

secure with the washer gaskets and union cap screw.

Tighten securely.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды