Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 87 / 535

2-49

TZ068

9. Install piston pin bearing washers on each side of the

bearing with the shoulder side facing the bearings.



NOTE: The shoulder side of the piston pin bearing

washers must face the bearing.

MD0251

10. Place pistons over the connecting rods with the

arrow (or indicator dot) pointing toward the exhaust

port; then secure with an oiled piston pin. Install new

piston pin circlips with the open ends up or down.

MD0293



NOTE: To aid in the circlip installation, install the

circlip to the inside of the piston before installing the
connecting rod.

MD0248

11. Place the cylinder base gasket into position on the

crankcase making sure the gasket is properly oriented

so the dowel pins will fit through the holes easily.

12. Rotate each piston ring until the ring ends are prop-

erly positioned with the pins in the ring grooves; then

apply oil to the piston assemblies and cylinder bores.

Using a ring compressor or the fingers, compress the

rings and slide the cylinder over the piston. Seat the

cylinder firmly onto the crankcase.

MD0229

13. Secure each cylinder by installing the four 6 mm and

eight 10 mm nuts. Tighten the 10 mm nuts in a criss-

cross pattern to 44 ft-lb and the 6 mm nuts to 96 in.-lb.

CAUTION

Make sure the new circlips are firmly seated in their
grooves and the open ends are pointed up or down
before continuing with assembly.

CAUTION

The cylinders should slide on easily. DO NOT force them
on or component damage may occur.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды