Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 76 / 535

background image

2-38

MD0275

6. Using Flywheel Puller, remove the flywheel.



NOTE: To ensure the cleanliness of the flywheel

magnets, place the flywheel (with the magnets facing
upward) on a clean bench.



NOTE: Do not remove the fan from the flywheel

assembly. If any damage or failure occurs with the fan
or the flywheel, it must be replaced as an assembly.

7. Remove the six cap screws securing the rear (intake-

side) shroud; then remove the shroud. Account for

the special washers.

MD0277

MD0067

8. Remove the rubber insulator grommet from the

crankcase; then remove two Phillips-head cap screws

securing the ignition timing sensor.

MD0075

MD0073

9. Remove the three Allen-head cap screws securing

the stator and remove it along with the timing sensor;

then carefully pull the wires through the hole in the

crankcase.

MD0072

CAUTION

To prevent damage to the crankshaft, install a protective
insert into the end of the crankshaft. The puller must
bottom on the insert and not on the crankshaft. Also, do
not thread puller bolts more than five threads into the
flywheel. Damage to the stator coils may result.

Manual

Table of Contents

«
...
74
75
76
77
78
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

2014 XF 2-STROKE

Бренд: Arctic Cat Страницы: 196

2011 Crossfire 600

Бренд: Arctic Cat Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды