Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 211 / 535

background image

3-32

742-207A

3. Install the body screws and lock nuts (C) from each

side and the self-tapping screws (B) from each side

securing the front bumper assembly to the chassis.

Tighten all hardware securely.

4. Connect the air temperature sensor and place the sen-

sor harness beneath the intake duct; then install the

duct into the silencer.



NOTE: To aid in installing the duct, it can be helpful

to apply a thin film of WD-40 to the air silencer seal
and to work the duct back and forth until the sleeve of
the duct is properly seated into the silencer.

5. Secure the intake duct to the upper frame with the

cap screw. Tighten securely.



NOTE: If the ECU was removed to gain access to

the duct cap screw, install the ECU using the two cap
screws. Tighten the cap screws securely; then con-
nect the harness plug-ins to the ECU.

FS202A

6. Using the illustration following step 2, secure the

left-side rear spar panel to the gas tank and support

tube with the three torx-head screws (D). Tighten the

screws securely.

7. Install the seat; then install the machine screw

(threads coated with blue Loctite #243) to the right

side of the seat support.

8. Place the rubber exhaust bumper into position on the

air silencer.

FS203A

9. Place gaskets on the resonator and exhaust manifold;

then install the expansion chamber. Secure the cham-

ber to manifold and upper frame with the springs.

10. Secure the console to the steering support with the

torx-head screws and tighten the screws securely;

then close the left-side and right-side access panels

and close the hood.

0743-777

Air Silencer

(1100 cc Non-Turbo)



NOTE: A number of servicing procedures for the

engine-related items require the air silencer be removed
and installed. Pay close attention to the



NOTE: pre-

ceding a particular servicing procedure that will direct
the technician to this sub-section for removing/install-
ing the air silencer.

REMOVING/INSPECTING/CLEANING

1. Adjust the seat to the lowest position; then while lift-

ing on the top forward part of the seat, remove the

machine screw from the right side of the seat support

assembly. Remove the seat.

CAUTION

Make sure to place the sensor harness beneath the
intake duct to avoid contact with exhaust components.

Manual

Table of Contents

«
...
209
210
211
212
213
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Blizzard 5500 1979

Бренд: Ski-Doo Страницы: 36

Бренд: Ski-Doo Страницы: 151

Бренд: Ski-Doo Страницы: 338

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды