Arctic Cat Sno Pro 120 2011 страница 386 Скачать руководство пользователя

Страница: 386 / 535

7-18

4. Position the shock links in the appropriate holes of

the idler arm brackets (see Chassis and Skid Frame

Mounting Locations in this section). Place a spacer

between the center of the brackets. Insert the axle

links into the upper shock link eyelets; then insert the

cap screw through the eyelets. Secure with a cap

screw, washer, and lock nut. Tighten securely.

MS031

SC023A

5. Place the upper shock eyelet with bushings between

the idler arm brackets making sure the spacer is

properly positioned between the brackets. Secure

with a cap screw and lock nut. Tighten securely.

SC019A



NOTE: Do not over-tighten the shock absorber cap

screw as the shock eyelet must be free to pivot.

6. Grease the idler arm and rear arm grease fittings with

a low-temperature grease.

7. Install the rear upper idler wheels, rear springs, and

offset pivot idler (see Rear Upper Idler Wheels/Rear

Springs in this sub-section).

8. Install the skid frame (see Installing Skid Frame in

this sub-section).



NOTE: Install the rear arm springs onto the adjuster

blocks after the skid frame has been installed.

Front Arm/Front Shock

Absorber/Front Inner Idler

Wheels



NOTE: The skid frame must be removed for this pro-

cedure (see Removing Skid Frame in this sub-sec-
tion), and the rear springs must be removed from the
adjusting cams.

REMOVING

1. Remove the lower cap screws and lock nuts securing

the limiter straps to the rail support. Account for flat

washers.

MS082A

2. Remove the cap screw and lock nut securing the

upper front shock absorber eyelet to the front arm.

Pull the shock eyelet free of the bracket. Account for

a serrated axle.

SC024A

3. Remove the cap screw and lock nut securing the

front arm to the slide rail; then remove the front arm

and account for the serrated axles, bushings, and an

axle tube.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды