Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 417 | Manualshive

Страница: 417 / 535

Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 417

7-49

7

FZ095A



NOTE: If removing the axle cap screws is necessary

for replacing the slide rail, install the cap screw from
the opposite side into the assembly to secure compo-
nents and aid in replacing the slide rail.

4. On the slide rail being removed, remove the cap

screws, lock nuts, and washers securing the idler

wheels and the idler wheel mounting blocks.

SC056A

5. Remove the cap screw, washers (if necessary), and

lock nut securing the front shock mount axle.

SC055C

6. Remove the cap screw and flat washer securing the

spring slide to the rail. Account for a spacer and the

slide block.

SC049B

7. Remove the cap screws securing the front arm

mounting bracket. Account for lock nuts.

MS188A

8. Remove the cap screw from the rear arm stop bush-

ing (A); then remove the cap screw (B) and lock nut

from the rear arm.

SC052A

9. Remove the idler wheel cap; then remove the cap

screw and flat washer securing the rear idler wheel.

Remove the idler wheel and adjuster bushing.

Manual

Table of Contents

«
...
415
416
417
418
419
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов