2-7
2
FZ021
FZ019
23. Check drive clutch/driven pulley alignment (see Sec-
tion 6). Install the drive belt. Check belt deflection.
Secure the belt guard.
NOTE: Make sure the rubber exhaust bumper is in
position on the close-off cover before installing the
expansion chamber.
FZ017A
24. Install the exhaust resonator and secure to the upper
frame with the washer, cap screw, and lock nut.
25. Place gaskets on the resonator and exhaust manifold;
then install the expansion chamber. Secure the cham-
ber to manifold and resonator with the springs.
NOTE: When installing the exhaust manifold
springs, the long hook portion of the spring must be
attached to the exhaust manifold or premature spring
failure will result.
26. Place the console into position on the headlight sup-
port bracket (do not secure the console with the torx-
head screws at this time); then connect the console/
main harness plug-in.
27. Install and close the left-side and right-side access
panels and the hood; then start the engine and warm
up to operating temperature. Verify that all compo-
nents are functioning properly and that coolant is cir-
culating through the cooling system properly.
28. Verify the tightening torque of the drive clutch.
29. Secure the console to the steering support with the
torx-head screws and tighten the screws securely;
then close the left-side and right-side access panels
and close the hood.
0743-777
CAUTION
Do not allow the driven pulley to “float” on the input
shaft. Damage to the driven pulley will occur.
CAUTION
Do not apply Loctite to the cap screw or damage to the
gear case will occur.
CAUTION
Never run the engine with the hood harness discon-
nected or damage to the electrical system will result.
CAUTION
After running the engine to the proper operating temper-
ature, shut the engine off; then open the hood and
access panels and inspect for any signs of coolant, gas-
oline, or oil leakage.
CAUTION
If the engine had a major overhaul or if any major com-
ponent was replaced, proper engine break-in proce-
dures must be followed (see Section 1). If the proper
engine break-in procedures are not followed, severe
engine damage may result.
Manual
Table of Contents
Содержание Sno Pro 120 2011
