Arctic Cat Sno Pro 120 2011 страница 448 Скачать руководство пользователя

Страница: 448 / 535

7-80

FZ052

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect all front arm weldments for cracks or unusual

bends; then inspect the front arm mounting brackets

for cracks and for elongated holes.

2. Closely inspect all tubing for cracks or unusual

bends.

3. Inspect the bearings, bushings, and front arm spacers

for wear or damage.

4. Inspect the shock absorber for damage and for any

signs of oil leakage especially at the point where the

shock shaft enters the shock body.

5. Inspect the shock absorber eyelet welds (at each end)

for any cracks, signs of separation, or for unthread-

ing.

INSTALLING

1. With the rubber bushing in place, install the axle into

the lower shock eyelet bushing assembly; then install

the two shim washers and two spacers.

CM246A

2. Place the front arm shock axle assembly into position

on the skid frame making sure the spacers and wash-

ers are properly positioned. Secure with the cap

screw, washer, and a new lock nut. Tighten to 40 ft-

lb.

FZ053

3. On the side that the idler wheel and mounting block

were removed from, secure the mounting block on

the slide rail with a cap screw and lock nut. Tighten

to 20 ft-lb.



NOTE: For proper alignment, install an idler wheel

cap screw and lock nut into the top mounting block
hole prior to tightening.

FZ055A

4. Secure the idler wheel to the mounting block with a

cap screw and a lock nut. Tighten cap screw to 20 ft-

lb.

FZ056

5. Install the axle into the front arm; then position the

front arm to the mounting location of the slide rail.

Secure with cap screws and lock nuts. Tighten to 40

ft-lb.



NOTE: Move the rear arm assembly forward enough

to allow the rear arm springs to be installed into the
slide blocks.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды