Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 67 / 535

2-29

FS216A



NOTE: At this point on the 500/600 cc LXR, install

the pinion bracket assembly to the engine with two
cap screws (coated with green Loctite #609). Tighten
to 20 ft-lb.

FS190A

2. Install the MAG-side engine mounting bracket to the

engine with the cap screws (F) (coated with blue

Loctite #243). Tighten to 23 ft-lb (500/600 cc) or 36

ft-lb (800 cc).

742-205B

742-201A

3. On the 500/600 cc, install the front lower engine

plate to the engine with four cap screws (G) (coated

with blue Loctite #243). Tighten to 50 ft-lb.

4. Place the engine into the engine compartment from

the MAG-side; then tip the engine forward and sup-

port the engine in this position. Connect the coolant

hose to the thermostat housing.

FS194A

FS217A



NOTE: At this point on the 500/600 cc LXR, insert

the flex-drive shaft into the pinion drive and secure
with the two set screws.

800 cc

500/600 cc

CAUTION

Direct the hose clamp screw to the back side of the ther-
mostat housing to avoid contacting the chassis when
the engine is lowered and secured.

800 cc

500/600 cc

800 cc

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды