Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя | Manualshive

Страница: 434 / 535

background image

7-66

CM256A



NOTE: If removing the front shock axle cap screw is

necessary to replace the slide rail, install the cap
screw from the opposite side into the assembly to
secure the axle and aid in replacing the slide rail.



NOTE: If the shock pads must be replaced, refer to

Shock Pads at the beginning of this procedure.

INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the slide rail for cracks (A), elongated holes

(B), or unusual bends.

MS220A

2. Inspect the wear strip for wear. The wear strip must

be 0.42 in. thick or thicker. If the wear strip measure-

ment is less than specified, replacement of both wear

strips is necessary.

AG530D

0743-189

INSTALLING

1. Place the slide rail into position. With the spacers

and washers in place, install the front arm shock

axle; then secure with the cap screw, washers, and

the lock nut. Tighten only until snug.

2. Install the rear arm cap screw and lock nut; then

install the rear arm limiter cap screw. Tighten only

until snug.

CM259

3. Install the cap screws (A) securing the three rail sup-

ports and rear arm limiter (B) to the slide rail; then

tighten the rail supports and rear arm limiter to 20 ft-

lb.

CM250B

Manual

Table of Contents

«
...
432
433
434
435
436
...
»

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды