manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 174 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 174

2-136

Troubleshooting Engine 

(2-Stroke Carbureted)

Problem: Engine Does Not Start (No Spark at Spark Plugs)

Condition

Remedy

1.

Ignition switch

 malfunctioning — not in RUN position

2.

Wiring harness

 shorting — connection poor

3.

Emergency stop switch knob

 in DOWN position — 

malfunctioning

4.

Throttle/ignition monitor switch

 adjusted too tight —

malfunctioning

5.

Carburetor safety switches

 adjusted incorrectly — 

malfunctioning

6.

Spark plugs

 fouled — damaged

7.

Spark-plug caps

 damaged — leaking — shorting

8.

High tension wires/coil

 loose — grounded — faulty

9.

CDI unit

 faulty

10.

Charge coil

 

(1)

 faulty

11.

Charge coil

 

(2)

 faulty

12.

Flywheel magnets

 weak

13.

Flywheel key

 sheared

1. Replace ignition switch — turn switch to RUN position
2. Repair — connect — replace wiring harness
3. Move knob to UP position — replace throttle switch

4. Adjust (loosen) throttle cable — replace throttle switch

5. Adjust — replace carburetor safety switches

6. Clean — gap — replace spark plugs
7. Replace spark-plug caps
8. Service — replace high tension wires/coil
9. Replace CDI unit

10. Replace coil
11. Replace coil
12. Replace flywheel
13. Replace key

Problem: Engine Does Not Start (No Fuel at Cylinders)

Condition

Remedy

1.

Gas tank

 empty

2.

Shut-off valve

 closed 

3.

Fuel hose

 broken — pinched

4.

Gas-tank vent — hose

 obstructed

5.

In-line fuel filter

 obstructed — damaged

6.

Fuel pump

 malfunctioning — faulty

7.

Impulse hose

 cracked — broken — pinched — discon-

nected

8.

Carburetors

 adjusted incorrectly — dirty — damaged

9.

Primary compression (crankcase)

 absent

1. Fill tank
2. Open shut-off valve
3. Replace — service hose
4. Remove obstruction — replace vent — hose
5. Remove obstruction — replace in-line fuel filter
6. Replace — repair — clean fuel pump
7. Replace — connect impulse hose

8. Troubleshoot — clean — replace carburetors
9. Repair — replace damaged — worn engine components

Problem: Engine Overheats

Condition

Remedy

1.

Spark plug heat range

 too hot

2.

Coolant

 low — absent

3.

Carburetors

 adjusted incorrectly — jetted incorrectly —

dirty

4.

Carburetor-to-cylinder air

 leak

5.

Heat exchangers

 no snow for cooling

6.

Rings/grooves

 carboned

7.

Exhaust ports

 obstructed

8.

Muffler

 obstructed

9.

Gas/air mixture

 incorrect

10.

Oil-injection pump

 malfunctioning — adjusted incor-

rectly

11.

Primary compression (crankcase)

 low — absent

12.

Ignition timing

 adjusted incorrectly

13.

Gasoline octane

 too low

14.

Water pump — thermostat

 damaged — faulty

1. Install lower heat-range spark plugs
2. Add coolant
3. Troubleshoot — clean carburetors — jet correctly

4. Replace — repair gaskets — intake flanges — service

intake ports

5. Select new trail — install ice studs to chew up hard

packed snow and ice

6. Clean — replace rings — pistons
7. Remove obstruction
8. Remove obstruction
9. Replace jets — adjust jet needle E-clip position

10. Replace — bleed — adjust oil-injection pump

11. Repair — replace damaged — worn engine components
12. Time ignition
13. Use 87 minimum octane gasoline
14. Replace — rebuild water pump — replace thermostat

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов