Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 50 / 535

2-12

0742-854

11. Route the gasline hose to the throttle body assembly

and secure the hose to the fuel rail. Tighten the clamp

securely; then using a cable tie, secure the hose to the

MAG-side engine mounting bracket.

12. Install the two coolant hoses to the MAG-side and

PTO-side of the crankcase (below the exhaust ports)

and the overflow hose; then tighten the coolant hose

clamps and the throttle body flange clamps.

FS271A

13. Apply a thin coat of high-temperature silicone sealant

to each exhaust port; then install the exhaust gaskets.

14. Apply a thin coat of high-temperature silicone seal-

ant to the mating surfaces of the exhaust manifold;

then install the exhaust manifold and secure with the

nuts. Tighten in a crisscross pattern to 15 ft-lb.

CM035

15. Install the side-plate brace onto the chassis and

secure the front of the brace with the four cap screws

(coated with blue Loctite #243). Tighten securely.

CM210A



NOTE: Install the two front lower cap screws first to

properly align the remaining cap screws.

16. After securing the front of the brace, secure the rear

of the brace and the steering support to the chassis

with the cap screws (coated with blue Loctite #243).

Tighten to 20 ft-lb.

CM209A

17. Fill the cooling system (see Liquid Cooling System

in Section 3).

18. Place the recoil starter into position and secure the

starter with the cap screws. Tighten to 96 in.-lb.

FC052

19. Slide the APV cable drums into the servomotor actu-

ator; then place the cable housings into position in

the servomotor.

CAUTION

When installing the throttle bodies, make sure the
gasline hose is properly routed to avoid premature wear
and/or contact with exhaust components.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды