Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 423 / 535

7-55

2. Inspect the slide rail for cracks. If any cracks are

found, replace the slide rail.

3. Using a straightedge, inspect the slide rail for any

unusual bends. With the slide rail removed, place the

straightedge along the bottom surface of the slide

rail. If the rail is found to be bent, it must be

replaced.

AG536D

INSTALLING



NOTE: Apply a light coat of grease to the slide rail

surface to aid in installing a new wear strip. Use a file
to remove any sharp edges on the lower portion of
the rail.

1. Align the wear strip with the openings (windows) in

the track and from the back, start the wear strip onto

the rail; then using a block of wood and a hammer,

drive the wear strip forward into position.

739-884A

2. Secure with a machine screw and lock nut. Tighten

to 50 in.-lb.

End Caps



NOTE: The skid frame does not have to be removed

for this procedure.

REMOVING

1. Remove the lock nut, washers, and cap screw secur-

ing the end cap.

CM222B

2. Using a hammer, tap the end cap off the rail.

CLEANING AND INSPECTING



NOTE: Whenever a part is worn excessively,

cracked, or damaged in any way, replacement is nec-
essary.

1. Inspect the end cap area of the slide rail for cracks

and wear.

CM223A

2. Inspect the end cap for any signs of cracking or wear.

MS290A

3. Clean both the slide rail area and the end cap. Using

compressed air, clean the areas of dirt and gravel.

! WARNING

Always wear an approved pair of safety glasses when
using compressed air.

! WARNING

Always wear an approved pair of safety glasses when
using compressed air.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды