Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 187 / 535

3-8

FS230

3. Apply a small amount of grease to the oil seal lips.

4. Using a pair of snap ring pliers, install the snap ring

securing the oil seal in the crankcase.

FS228

5. Using the seal driver, carefully install the outer water

pump mechanical seal. Gently tap the seal down into

position until it seats itself against the crankcase.

FS232

6. Apply a light coat of grease to the sealing surface of

the oil-injection pump driveshaft; then install Oil

Seal Protector Tool at the end of the shaft. Twist the

shaft while pushing it through the oil and water

pump seals until the shaft gear engages with the

drive gear of the crankshaft; then remove the tool.

FS233A

IO025B

7. Position the shim on the oil pump end of the shaft;

then with the O-ring installed on the retainer, install

the oil-injection pump retainer.

IO026A

8. With the O-ring in place on the oil-injection pump,

align the pump with the shaft; then install the pump.

Secure with the cap screws (coated with blue Loctite

#243) (B) and tighten to 96 in.-lb. Place the lower

check valve into position; then secure with the gas-

kets and cap screw (A). Tighten to 48 in.-lb.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды