Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 288

Страница: 288 / 535

5-27

ZJ248A

6. Secure the oil tank to the chassis with the three cap

screws; then tighten securely.

ZJ146A



NOTE: At this point, fill and bleed the oil and cool-

ing systems (see Section 3).

Troubleshooting Electric

Start

Ignition Timing (2-Stroke)



NOTE: The ignition timing is not adjustable, but it

can be checked and/or verified.

CHECKING

1. Connect a timing light to the MAG-side spark plug

lead.

2. Using a shielded safety stand, raise the rear of the

snowmobile off the floor and start the engine. Gradu-

ally increase the engine speed to the specified RPM;

the pointer should align with the proper timing mark

on the flywheel.

Brakelight Switch

TESTING/REMOVING



NOTE: On the F-Series/T-Series/Z1 models to

access the brakelight switch connector, the two rear
console torx-head screws must be removed and the
console must be lifted upward and forward.

1. Disconnect the brakelight switch black and brown

two-wire connector (located below the steering sup-

port).

2. To test the brakelight switch, connect one tester lead

to the brown terminal; then connect the other lead to

the black terminal.

3. With the brake lever compressed, the meter must

read 1 ohm or less resistance. With the brake lever

released, the meter must read OL (open). If the meter

does not read as specified, the brakelight switch is

defective and must be replaced.

4. To remove the switch, remove the snap ring; then

remove the pin securing the brake lever to the control

assembly.

5. Using a small flat-blade screwdriver, compress the

tabs of the switch; then push the switch toward the

end of the handlebar and out of the control assembly.

CM108A

INSTALLING

1. Slide the brakelight switch into the brake control

assembly until the self-locking tabs snap into posi-

tion. Lightly pull the switch body to ensure the

switch is properly secured.

2. Install the brake lever and secure with the pin and

snap ring.

Problem: Hot or Smoking Wires

Condition

Remedy

System

wired incor-

rectly

1. Check wiring against wir-

ing diagram

Problem: Starter Does Not Turn Over

Condition

Remedy

Battery

discharged

Connection

loose

Grounding

improper

Fuse

blown - not

installed

1. Check/charge the battery

2. Check tightness of all con-

nections

3. Check round connections

4. Check - replace fuse

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 288 / 535

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы: