manualshive.com logo in svg

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию, Страница: 213 / 535

Поделиться
Скачать
Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя страница 213

3-34

IO053A

NOTE: After the gas tank vent hose has been

removed, plug the hose outlet of the gas tank to avoid
gas leakage.

10. Remove the two torx-head cap screws securing the

air silencer to the chassis; then loosen the screws on

the clamps securing intake boot to the throttle bod-

ies.

ZJ013A

11. Remove the breather hose from the air silencer.

ZJ096B

12. Move the air silencer far enough to the right to

bypass the air silencer mounting bracket; then slide

the air silencer rearward and disconnect the air tem-

perature sensor. Remove the air silencer from the

chassis.

ZJ015A

13. Inspect the throttle valve thoroughly for carbon resi-

due buildup. If signs of carbon buildup exist, the

throttle body should be cleaned (see Fuel System

(EFI) - Throttle Body Assembly in Section 4).

ZJ125

14. Remove the air temperature sensor from the air

silencer.

ZJ126A

15. Split the protective foil at the seam of the air

silencer; then remove the retaining clips securing the

dual intake boot to the air silencer.

16. Remove the seven machine screws and separate the

air silencer halves.

17. Inspect the air silencer thoroughly for any foreign

material; then clean the air silencer with soap and

water. Dry the air silencer thoroughly prior to install-

ing.

CAUTION

The gasoline supply hose may be under pressure.
Place an absorbent towel around the connection to
absorb gasoline; then remove the hose slowly to
release the pressure.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов