Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 351 / 535

6-28

2. Remove the drive belt (see Drive Belt in this sec-

tion); then remove the driven pulley.

3. Tip the snowmobile onto its right side and use a suit-

able support to protect the snowmobile from the

floor.

4. Remove the drain plug from the gear case; then

install a drain adapter fitting with hose into the drain

plug hole.

0743-456

741-636A



NOTE: To aid in draining the lubricant, it is advis-

able to fashion a drain adapter by using the Gear
Case Drain Fitting and a length of 3/8-in. hose.

5. Tip the snowmobile back to the upright position;

then place a drain pan on the floor next to the drain

hose and tip the snowmobile toward its left side far

enough to allow the lubricant to drain from the gear

case into the drain pan.



NOTE: It is critical that the snowmobile is on a level

surface to ensure the lubricant drains properly and
completely.

6. Secure the snowmobile in this position until the

lubricant is completely drained.

7. When the lubricant has completely drained form the

gear case, tip the snowmobile back to the upright

position, remove the drain adapter, and install and

securely tighten the drain plug; then remove the

check/fill plug.

8. Pour the recommended amount of Arctic Cat ACT

Drive Flush Fluid into the check/fill hole; then install

the plug. Tighten securely.

9. Install the driven pulley; then install the drive belt

(see Drive Belt sub-section) and the belt guard.

10. Install the access panels.

11. Using a shielded safety stand, raise the rear of the

snowmobile off the floor making sure the track is

free to rotate.

12. Start the engine and accelerate slightly. Use only

enough throttle to turn the track several revolutions.

SHUT ENGINE OFF.

13. Remove the access panels; then remove the belt

guard.

14. Remove the drive belt (see Drive Belt sub-section);

then remove the driven pulley.

15. With the stand in place, tip the snowmobile onto its

right side.

16. Remove the drain plug from the gear case; then

install the drain adapter fitting with hose into the

drain plug hole.

17. Tip the snowmobile back to the upright position;

then place a drain pan on the floor next to the drain

hose and with the stand in place, tip the snowmobile

toward its left side far enough to allow the flush fluid

to drain from the gear case into the drain pan.

18. Secure the snowmobile in this position until the flush

fluid is completely drained.

19. When the fluid has completely drained from the gear

case, tip the snowmobile back to the upright position,

remove the drain adapter, and install and tighten the

drain plug to 12 ft-lb; then remove the check/fill

plug.

20. Pour the exact amount (see appropriate specification

sheet) of Arctic Cat Synthetic ACT Gear Case Fluid

into the check/fill hole; then install the plug. Tighten

to 12 ft-lb.

CAUTION

All old lubricant must be drained from the gear case
prior to flushing the gear case.

CAUTION

Do not add more or less than the recommended
amount of flush fluid to the gear case.

! WARNING

DO NOT stand behind the snowmobile or near the
rotating track. NEVER run the track at high speed
when the track is suspended.

CAUTION

All flush fluid must be drained from the gear case
prior to filling with new lubricant.

CAUTION

The correct lubricant to use in the gear case is Arctic
Cat Synthetic ACT Gear Case Fluid. Any substitute
may cause serious damage to the drive system.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды