Arctic Cat Sno Pro 120 2011 Скачать руководство пользователя

Страница: 220 / 535

3-41

TZ061

13. Connect the coolant return hose to the turbo and

secure with the hose clamp.

TZ060A

14. Connect the air bypass hose and the air bypass con-

trol valve hose to the intake pipe and secure with the

clamps.

743-983A

15. Install the hose from the waste gate control valve to

the elbow fitting of the turbocharger and secure with

the clamp.

TZ086B

16. Connect the air silencer hose to the turbo and secure

with the clamp; then secure the air silencer to the

right-side upper frame with the cap screw.

743-983B

17. Position the intercooler into the grommets of the

mounting bracket; then connect the intercooler hoses

to the turbo and to the intake plenum. Tighten all

hose clamps securely.

18. Start the engine and allow the engine to idle for at

least two minutes before increasing RPM to allow

for proper lubrication of the turbo shaft and bearings.

19. After running the engine, check the oil and coolant

levels.



NOTE: If adding coolant is required, bleed the cool-

ing system (see appropriate Liquid Cooling System
in this section).

Arctic Power Valve (APV)

System (2-Stroke)

The Arctic Power Valve (APV) System adjusts the size of

the exhaust ports to produce maximum horsepower on

the top end while providing excellent low end power and

increased touring fuel economy.

Manual

Table of Contents

Содержание Sno Pro 120 2011
























































































































































































































































































































































































































































































































































Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды

Arctic Cat Sno Pro 120 2011, Руководство по обслуживанию

Результаты поиска

Содержание Sno Pro 120 2011

Отзывы:

Похожие инструкции для Sno Pro 120 2011

Бренды по названию

Популярные бренды